Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
products:approach-training [2017/10/25 14:34] Andreas Breitschopp |
products:approach-training [2017/11/02 18:43] (current) Andreas Breitschopp [Options] |
||
---|---|---|---|
Line 56: | Line 56: | ||
If the runway is ILS enabled the correct altitude above ground will be calculated using the runway-specific glideslope degree. Otherwise the default of 3° will be used. | If the runway is ILS enabled the correct altitude above ground will be calculated using the runway-specific glideslope degree. Otherwise the default of 3° will be used. | ||
- | All parameters like distance to landing point for the two final positions, distance for the base positions or altitude above ground for the downwind positions can be configured in the [[features:settings#position|Settings]] module. | + | All parameters like distance to landing point for the two final positions, distance for the base positions or altitude above ground for the downwind positions can be configured in the [[products:approach-training#position|Settings]] module. |
==== Helipads ==== | ==== Helipads ==== | ||
Line 86: | Line 86: | ||
Choose one of four pre-defined flight levels to start your airworks. | Choose one of four pre-defined flight levels to start your airworks. | ||
- | Of course, also these altitudes can be easily changed in the [[features:settings#airworks|Settings]] module. | + | Of course, also these altitudes can be easily changed in the [[products:approach-training#airworks|Settings]] module. |
==== Custom Location ==== | ==== Custom Location ==== | ||
Line 128: | Line 128: | ||
Here you can find several options like speed and gear/flaps status that are used when placing the aircraft. | Here you can find several options like speed and gear/flaps status that are used when placing the aircraft. | ||
- | All options are saved upon change and can even be defined on a per-aircraft level when aircraft profiles are enabled in the [[features:settings#options_on_position_change|Settings]] module. | + | All options are saved upon change and can even be defined on a per-aircraft level when aircraft profiles are enabled in the [[products:approach-training#options_on_position_change|Settings]] module. |
:i: Note: When aircraft is placed on ground gear is always extended and ILS frequency can only be set obviously if the runway is ILS enabled. | :i: Note: When aircraft is placed on ground gear is always extended and ILS frequency can only be set obviously if the runway is ILS enabled. | ||
Line 224: | Line 224: | ||
=== General === | === General === | ||
- | {{https://www.fs-flightcontrol.com/img/manual/features/settings/position-general.png?nolink|}} | + | {{https://www.fs-flightcontrol.com/img/manual/steam/approach-training/settings-appraoch-training-general.png?nolink|}} |
You can enable or disable some automatizations after an aircraft position is changed. | You can enable or disable some automatizations after an aircraft position is changed. | ||
Line 298: | Line 298: | ||
== Colors for Display Type == | == Colors for Display Type == | ||
- | {{https://www.fs-flightcontrol.com/img/manual/features/settings/statistics-colors-table.png?nolink|}} | + | {{https://www.fs-flightcontrol.com/img/manual/steam/approach-training/settings-landing-analysis-colors-table.png?nolink|}} |
Here all currently defined colors are displayed for the selected display type. | Here all currently defined colors are displayed for the selected display type. | ||
Line 306: | Line 306: | ||
=== Print Options === | === Print Options === | ||
- | {{https://www.fs-flightcontrol.com/img/manual/features/settings/statistics-print-options.png?nolink|}} | + | {{https://www.fs-flightcontrol.com/img/manual/steam/approach-training/settings-landing-analysis-print-options.png?nolink|}} |
For statistics printing you can define here which printer should be used. | For statistics printing you can define here which printer should be used. |