Differences

This shows you the differences between two versions of the page.

--- features:aircraft [2020/03/16 13:23]
Andreas Breitschopp [Attitude]
+++ features:aircraft [2023/01/17 10:40]
Andreas Breitschopp
@@ Line 11: / Line 11: @@
 Some generic aircraft gauges are displayed on this page.
-You can click on each of those gauges to detach them into a separate window.
 ==== Six Pack Gauges ====
@@ Line 25: / Line 23: @@
 And here you see a generic Primary Flight Display (PFD).
+==== Detach ====
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/gauges-detach.png?nolink|}}
+You can click on each of those gauges to detach them into a separate window.
+Use the little pin icon in the title bar to keep the gauge window always on top.
 ===== Aircraft Status =====
@@ Line 30: / Line 36: @@
 This aircraft status page will get you an overview about all relevant aircraft parameters.
-==== Airspeed ====
+==== Speed ====
-{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/status-airspeed.png?nolink|}}
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/status-speed.png?nolink|}}
 Here you can see the indicated and true airspeed of the aircraft.
@@ Line 68: / Line 74: @@
 You see the current load and voltage of all electrical bus system, see if the battery is currently charging or not and can trigger the APU or external/ground power if needed.
-:i: Note: Some options are only available if ProSim, AST or JeeHell is connected.
+:i: Note: Some options are only available with certain third party aircraft options enabled.
 ==== Pressurization System ====
@@ Line 83: / Line 89: @@
 Here you can open and close again the exit doors of your aircraft.
+==== Glider Towing ====
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/status-glider-towing.png?nolink|}}
+Control glider towing and release in this section.
+:i: Note: The winch option is only available with X-Plane.
 ===== Engines =====
@@ Line 106: / Line 120: @@
 There are quick access buttons for 0 %, 25 %, 75 % and 100 %, but you can also enter any specific percentage you want. Also reverse trust can be enabled for a specific or all engines by clicking on the button ''Reverse Trust'' if the engine supports that.
-:i: Note: The engine quick start options are only available if ProSim is connected.
+:i: Note: The engine quick start options are only available with certain third party aircraft options enabled.
 ==== Engine Switches ====
@@ Line 152: / Line 166: @@
 And use these buttons to control even more aircraft switches.
-===== TCAS Alert =====
+===== TCAS Traffic =====
-{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/tcas-alert.png?nolink|}}
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/tcas-traffic.png?nolink|}}
 Here you can generate an aircraft that will trigger a TCAS alert.
@@ Line 160: / Line 174: @@
 First choose the aircraft type that should be generated. By default this is the aircraft you are currently flying.
-Next you can define the location where the aircraft is being generated. You can either select one of the pre-defined location or enter a specific degree (in relation to the current aircraft heading).
+Next you can define the location where the aircraft is being generated. You can either select one of the pre-defined location or enter a custom degree (in relation to the current aircraft heading).
 Now enter the distance to the generated aircraft and the true airspeed it will be flying towards you.
-You can also define a specific altitude (by default exactly the altitude your aircraft is currently at) and a vertical speed.
+You can also define a relative altitude (by default it is generated exactly at the altitude your aircraft is currently at) and a vertical speed.
-Finally trigger the aircraft generation with the button ''Generate TCAS Aircraft'' and remove all previously generated aircraft with the button ''Remove all TCAS Aircraft'' again.
+Finally trigger the aircraft generation with the button ''Generate Intruder Aircraft'' and remove all previously generated aircraft with the button ''Remove all Intruder Aircraft'' again.
+:i: Note: The intruder aircraft type and vertical speed cannot be set if X-Plane is used. Also only one intruder at the same time is supported for X-Plane.
 ===== ATC Control =====
@@ Line 175: / Line 191: @@
 :i: Note: If X-Plane is used you can only show or hide the ATC window here.
+===== Change Aircraft =====
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/change.png?nolink|}}
+To change your aircraft in the simulator first select the new aircraft from the list and then click on the button ''Change Aircraft''.
+With a commercial license you can restrict the aircraft available for selection in this dialog in the [[features:settings#change_aircraft|Settings]] module.
+:i: Note: The simulator does not provide a preview image for all aircraft.
+===== Custom Buttons =====
+{{https://www.fs-flightcontrol.com/img/manual/features/aircraft/custom.png?nolink|}}
+This section will be available when you have created custom bottoms in the [[features:settings#custom_buttons|Settings]] module.
+The buttons shown above are the result of the [[features:settings#examples_and_reference|examples here]].

User Tools

Site Tools

Differences

Page Tools